TB-IB301
Optional Board
PCB board
IP Camera
up to 4K/8MP
TENBO
L50*W48*H20mm
Shernzhen, China
8529904900
Product Description
| Interface Type | No. | Name | Description |
| PWR1: Power interface | DC12V Power input | ||
| J1: Audio and video, alarm in&out, RS485 port | 1 | LINEIN | Audio input signal |
| 2 | LINEOUT | Audio output signal | |
| 3 | GND | Power ground | |
| 4 | RS -485+ | RS -485 Line A | |
| 5 | RS -485 - | RS -485 Line B | |
| 6 | GND | Power ground | |
| 7 | ALARM_IN | Electrical level alarm input | |
| 8 | ALARM_OUTP | Level alarm output high (valid) | |
| 9 | ALARM OUTN | Level alarm output low (valid) | |
| JP2: UART Port | 1 | 3.3V | 3.3V Power output |
| 2 | RXD | UART port, receiving signal (3.3V), using VISCA protocol | |
| 3 | TXD | UART port, sending signal (3.3V), using VISCA protocol | |
| 4 | GND | Power ground | |
| P1: RJ45 Ethernet | 1 | TX+ | Adaptive network port, physical signal sending (+ differential) |
| 2 | TX- | Adaptive network port, physical signal sending (- differential) | |
| 3 | RX+ | Adaptive network port, physical signal receiving (+ differential) | |
| 4 | NC | Empty | |
| 5 | NC | Empty | |
| 6 | RX- | Adaptive network port, physical signal receiving (- differential) | |
| 7 | NC | Empty | |
| 8 | NC | Empty | |
| V1: CVBS Coaxial output interface | Analog video signal output | ||
| JP1: 36Pin for interface board | 1 | DC12V | DC12V Power output |
| 2 | DC12V | DC12V Power output | |
| 3 | DC12V | DC12V Power output | |
| 4 | GND | Power ground | |
| 5 | GND | Power ground | |
| 6 | CVBS | Analog video output | |
| 7 | GND | Power ground | |
| 8 | LINE_OUT | Audio output | |
| 9 | GND | Power ground | |
| 10 | LINE_IN | Audio input | |
| 11 | Empty | Empty | |
| 12 | TPTX+ | Adaptive network port, physical signal sending (+ differential) | |
| 13 | TPTX - | Adaptive network port, physical signal sending (- differential) | |
| 14 | TPRX+ | Adaptive network port, physical signal receiving (+ differential) | |
| 15 | TPRX - | Adaptive network port, physical signal receiving (- differential) | |
| 16 | GND | Power ground | |
| 17 | LINK# | LINK# indicator | |
| 18 | ACT# | ACT# indicator | |
| 19 | ALARM_OUT | Alarm output | |
| 20 | ALARM_IN | Alarm input | |
| 21 | GND | Power ground | |
| 22 | SD_EN | SDIO card power enable | |
| 23 | Empty | Empty | |
| 24 | SD_CD | SDIO data card detection pin | |
| 25 | SD_CLK | SD Card clock signal | |
| 26 | SD_CMD | SDIO_CMD Card command | |
| 27 | SD_DATA3 | SDIO data bit3 | |
| 28 | SD_DATA2 | SDIO data bit2 | |
| 29 | SD_DATA1 | SDIO data bit1 | |
| 30 | SD_DATA0 | SDIO data bit0 | |
| 31 | GND | Power ground | |
| 32 | RS485 - | RS-485 B Line, using PELCO protocol | |
| 33 | RS485+ | RS-485 A Line, using PELCO protocol | |
| 34 | TTL_TXD | UART port, sending signal (3.3V) at the camera module end, using VISCA protocol | |
| 35 | TTL_RXD | UART port, receiving signal (3.3V) at the camera module end, using VISCA protocol | |
| 36 | SYS_RSET_N | External key reset signal input |
