Acid and alkali resistant vertical pump
1. Adopt brand motor, high heat resistance, strong electric shock resistance, low energy consumption, high efficiency, energy saving and environmental protection.
2. Using imported raw materials, high temperature resistance and corrosion resistance are stronger.
3. Front cover integrated molding design, no welding points. Effectively prevent liquid leakage and corrosion during use.
4. Dry liquid seal design, reverse design of impeller, bearing end cap oil seal design, can protect the motor to prevent acid gas from entering and corrosion, extend the service life of the motor and pump.
Vortex type vertical pump:
1. No water idling, will not damage the pump under idling.
2. Unique liquid seal design. It can effectively prevent damage to the motor caused by liquid backflow due to instantaneous motor shutdown.
3. Vortex flow channel design, make full use of the principle of fluid mechanics, increase the flow rate, improve efficiency.
4. High efficiency water conservancy design. With fluid analysis, the flow characteristics can be mastered to reduce the loss of flow force. Improve blade flow efficiency.
5. The use of international A-grade PP raw materials, high temperature resistance, corrosion resistance is stronger.
6. Install acid and alkali resistant seals at the motor output shaft and pump bottom respectively.Double layer protection prevents chemical gases from damaging motor bearings.
| Model | Curve | Aperture (DN) | Power (HP) | Speed (r/min) | Phase (Φ) | Poles (P) | Total Capacity 50Hz/60Hz (L/min) | Total Head 50Hz/60Hz (m) | ||
| 5OHz | 60Hz | Inlet (Inch) | Outlet (Inch) | |||||||
| MIT-40VK-1 | a | A | 50 | 40 | 1 | 2900 | 3 | 2 | 190/230 | 8/10 |
| MIT-40VK-2 | b | B | 50 | 40 | 2 | 2900 | 3 | 2 | 290/320 | 15/18 |
| MIT-40VK-3 | c | C | 50 | 40 | 3 | 2900 | 3 | 2 | 360/380 | 20/24 |
| MIT-40VK-5 | d | D | 50 | 40 | 5 | 2900 | 3 | 2 | 435/450 | 28/32 |
| MIT-50VK-3 | e | E | 50 | 50 | 3 | 2900 | 3 | 2 | 465/490 | 21/23 |
| MIT-50VK-5 | f | F | 50 | 50 | 5 | 2900 | 3 | 2 | 520/550 | 26/28 |
| MIT-65VK-7.5 | g | G | 80 | 65 | 7.5 | 2900 | 3 | 2 | 935/950 | 26/30 |
| MIT-65VK-10 | h | H | 80 | 65 | 10 | 2900 | 3 | 2 | 1135/1220 | 35/38 |
| MIT-80VK-7.5 | i | I | 80 | 80 | 7.5 | 2900 | 3 | 2 | 1240/1250 | 26/30 |
| MIT-80VK-10 | j | J | 80 | 80 | 10 | 2900 | 3 | 2 | 1470/1470 | 33/36 |
| MIT-80VK-15 | k | K | 80 | 80 | 15 | 2900 | 3 | 2 | 1635/1800 | 37/39 |
| MIT-100VK-15(Vortex type) | A | 125 | 100 | 15 | 2900 | 3 | 2 | 2680 | 31 | |
| MIT-100VK-20(Vortex type) | B | 125 | 100 | 20 | 2900 | 3 | 2 | 3400 | 30 | |
| MIT-100VK-25(Vortex type) | C | 125 | 100 | 25 | 2900 | 3 | 2 | 3600 | 31 | |
| MIT-100VK-30(Vortex type) | D | 125 | 100 | 30 | 2900 | 3 | 2 | 4180 | 38 | |
| MIT-125VK-15(Vortex type) | E | 125 | 125 | 15 | 2900 | 3 | 2 | 2500 | 30 | |
| MIT-125VK-20(Vortex type) | F | 125 | 125 | 20 | 2900 | 3 | 2 | 4400 | 27 | |
| MIT-125VK-25(Vortex type) | G | 125 | 125 | 25 | 2900 | 3 | 2 | 4520 | 32 | |
| MIT-125VK-30(Vortex type) | H | 125 | 125 | 30 | 2900 | 3 | 2 | 4840 | 40 | |
| MIT-15VK-1/15(Stainless steel) | a | A | 25 | 15 | 1/15 | <1.1 | 1 | 50/75 | 3/4 | |
| MIT-15VK-1/8(Stainless steel) | b | B | 25 | 15 | 1/8 | <1.1 | 1 | 60/85 | 3.5/5 | |
| MIT-15VK-1/6(Stainless steel) | c | C | 25 | 15 | 1/6 | <1.1 | 1 | 70/100 | 3.8/6 | |
| MIT-25VK-1/4(Stainless steel) | d | D | 40 | 25 | 1/4 | <1.1 | 1&3 | 90/110 | 5/6 | |
| MIT-25VK-1/3(Stainless steel) | e | E | 40 | 25 | 1/3 | <1.1 | 1&3 | 105/130 | 6/7 | |
| MIT-25VK-1/2(Stainless steel) | f | F | 40 | 25 | 1/2 | <1.1 | 1&3 | 145/160 | 7/8 | |
