PTFE Products
Tank Reactor
Steel Liner
Customized
Customized
Positive
Customized
Customized
Customized
Combined
Automatic
New
JSLW
Wooden Packing
Support customization
China
39209910
Product Description
Product Description:
Hydrothermal synthesis reactor:
Brief introduction:
Hydrothermal synthesis reactor is the reactor that provides synthetic chemical substances in certain temperature and pressure conditions.
Features:
1.It is made of quality non-magnetic0Cr18Ni9Ti of stainless steel.
2.The kettle body and kettle cover are sealed by durable and reliable line seal structure with long-term stability to leak free seal.
3.Stainless steel chassis, stainless steel kettle body, stainless steel gland, stainless steel kettle cover and extended stainless steel rods.
4.With PTFE liner, double care, acid and alkali, resistant to high temperature of 200ºC
5.Thickening processing PTFE cover, not easy to soften.
6.Beautiful appearance, reasonable structure and easy to operate.
7.Good corrosion resistance.
Working Temperature:PTFE≤230°C ,Safe Temperature is 200°C; PTFE≤280°C Safe Temperature is 260°C. Strictly require temperature not to exceed the maximum use temperature.
Working Pressure:The pressure of the actual reactant in the ketle shall not exceed 3Mpa. The pressure generated by material synthesis requires the customer to accurately calculate the pressure generated at the temperature according to the different materials used in the experiment. The experiment must be conducted within the
normal allowable range to ensure the safety of the experimenter.
PTFE Lining and PPL Lining:PPL is a kind of synthetic material added to PTFE, and its properties are better than those of PTFE alone. PPL can be used continuously at 260 °C, with the highest operating temperature 280 °C-300 °C, very low friction coefficient, good wear resistance and excellent chemical stability.
Loading Capacity:The amount of solvent added to the reaction depends on diferent tests, generally 60%~80% of the inner cup capacity. If the reactant produces a large amount of gas, it is recommended to cool overnight and use perchloric acid. Hydrogen peroxide and so on should pay special attention!
Heating Equipment and Safety:Generally, the laboratory uses an oven for heating. The actual temperature control inside the oven should reach±2 °C to avoid excessive overheating.
When the oven starts to heat up, there shall be no personnel in the room to prevent explosion injury! Enter the tank only after it is cooled to room temperature.
Necessary safety protection measures shall be taken when taking the tank, such as face protection, hand protection, respiratory protection, etc.
Product Display:
Product Packaging:
Factory And Equipment:
Our Service
1. Providing technical consultation.
2. Samples are free.
3.We could customize various products with your brand logo according to your requirements.
4. Your inquiry will be replied within 1 hours during working time,Within 24 hours when rest time.
5.Orders will be produced exactly as request and approved samples.
6. Before shipment,our QC will have inspection to make sure the quality.
7.We always try best to ensure every order to delivery in time.
8.Special packaging according to request.
Hydrothermal synthesis reactor:
Brief introduction:
Hydrothermal synthesis reactor is the reactor that provides synthetic chemical substances in certain temperature and pressure conditions.
Features:
1.It is made of quality non-magnetic0Cr18Ni9Ti of stainless steel.
2.The kettle body and kettle cover are sealed by durable and reliable line seal structure with long-term stability to leak free seal.
3.Stainless steel chassis, stainless steel kettle body, stainless steel gland, stainless steel kettle cover and extended stainless steel rods.
4.With PTFE liner, double care, acid and alkali, resistant to high temperature of 200ºC
5.Thickening processing PTFE cover, not easy to soften.
6.Beautiful appearance, reasonable structure and easy to operate.
7.Good corrosion resistance.
Working Temperature:PTFE≤230°C ,Safe Temperature is 200°C; PTFE≤280°C Safe Temperature is 260°C. Strictly require temperature not to exceed the maximum use temperature.
Working Pressure:The pressure of the actual reactant in the ketle shall not exceed 3Mpa. The pressure generated by material synthesis requires the customer to accurately calculate the pressure generated at the temperature according to the different materials used in the experiment. The experiment must be conducted within the
normal allowable range to ensure the safety of the experimenter.
PTFE Lining and PPL Lining:PPL is a kind of synthetic material added to PTFE, and its properties are better than those of PTFE alone. PPL can be used continuously at 260 °C, with the highest operating temperature 280 °C-300 °C, very low friction coefficient, good wear resistance and excellent chemical stability.
Loading Capacity:The amount of solvent added to the reaction depends on diferent tests, generally 60%~80% of the inner cup capacity. If the reactant produces a large amount of gas, it is recommended to cool overnight and use perchloric acid. Hydrogen peroxide and so on should pay special attention!
Heating Equipment and Safety:Generally, the laboratory uses an oven for heating. The actual temperature control inside the oven should reach±2 °C to avoid excessive overheating.
When the oven starts to heat up, there shall be no personnel in the room to prevent explosion injury! Enter the tank only after it is cooled to room temperature.
Necessary safety protection measures shall be taken when taking the tank, such as face protection, hand protection, respiratory protection, etc.
| Model | Capacity | Outer diameter of shell | Shell height | Outer diameter of lining | Lining height |
| LW-25 | 25ml | 45 | 117 | 32.8 | 61 |
| LW-50 | 50ml | 53 | 140 | 40 | 78 |
| LW-100 | 100ml | 62 | 155 | 48.7 | 94 |
| LW-150 | 150ml | 72 | 189 | 57.5 | 114 |
| LW-200 | 200ml | 82 | 210 | 62.7 | 133 |
| LW-250 | 250ml | 82 | 219 | 64.9 | 133 |
| LW-300 | 300ml | 91 | 226 | 74 | 150 |
| LW-500 | 500ml | 104 | 243 | 83.5 | 164 |
| LW-1000 | 1000ml | 146 | 232 | 117 | 150 |
| LW-2000 | 2000ml | 270 | 220 | 180 | 141 |
| Remark | Heating and Cooling Rate ≤5ºC/min | ||||
| The above dimensions are in mm | |||||
Product Display:
Product Packaging:
Factory And Equipment:
Our Service
1. Providing technical consultation.
2. Samples are free.
3.We could customize various products with your brand logo according to your requirements.
4. Your inquiry will be replied within 1 hours during working time,Within 24 hours when rest time.
5.Orders will be produced exactly as request and approved samples.
6. Before shipment,our QC will have inspection to make sure the quality.
7.We always try best to ensure every order to delivery in time.
8.Special packaging according to request.
