B2N
Hall Type
Analog Output
SemiConductor Integrated
Plastic
0.5G
Switching Power Supply
IP65
ISO
Customized
B2n- 0.5A/ B2n-1A/ B2n-2A/ B2n-5A/ B2n-10A/ B2n-20
0.5-20A
1-30A
400 Ohm
+-12V, +-15V
Less Than 20+ Ipx(Np/Ns)
Less Than 0.1
@ 50Hz, AC, 1min 2.5kv
DHL, TNT, FedEx...
HEYI
Green Plastic Film
CE, ISO, Rohs
Liushi, Yueqing, Zhejiang Province, China
8542390000
Product Description
B2N series current sensor is a closed loop device based on the measuring principle of the hall effect and null balance method, with a galvanic isolation between primary and secondary circuit. It provides accurate electronic measurement of DC, AC or pulsed currents.
·AC variable speed drives
·Static converters for DC motor drives
·Battery supplied applications
·Uninterruptible Power Supplies (UPS)
·Switched Mode Power Supplies (SMPS)
·Power supplies for welding applications
Remarks:
1. All dimensions are in mm.
2. General tolerance ±1mm.
1. When the current will be measured goes through a sensor, the voltage will be measured at the output end. (Note: The false wiring may result in the damage of the sensor)
2. Custom design in the different rated input current and the output voltage are available.
·UL94-V0.
·EN60947-1:2004
·IEC60950-1:2001
·EN50178:1998
·SJ 20790-2000
| Electrical data (Ta=25ºC±5ºC) |
| Type | B2N- 0.5A | B2N- 1A | B2N- 2A | B2N- 5A | B2N- 10A | B2N- 20A | Unit |
| Rated current(Ipn) | 0.5 | 1 | 2 | 5 | 10 | 20 | A |
| Measure range(Ip) | 1 | 2 | 4 | 10 | 20 | 30 | A |
| Turns ratio(Np/Ns) | 30:1500 | 15:1500 | 8:1600 | 3:1500 | 2:2000 | 1:2000 | T |
| Internal resister | 400 | 400 | 400 | 400 | 400 | 400 | Ω |
| Rated output | @Ip=±Ipn ±4±0.5% | V | |||||
| Supply voltage | ±12,±15 | V | |||||
| Power Consumption | ≤20+ IpX(Np/Ns) | mA | |||||
| Zero offset voltage | @Ip=0 ≤±20 | mV | |||||
| Offset voltage drift | @ -40~+85ºC ≤±0.5 | mV /ºC | |||||
| Linearity | @Ip=0-±Ipn ≤0.1 | %FS | |||||
| Response time | @100A/μ S,10%-90% ≤1 | μS | |||||
| Galvanic isolation | @ 50HZ,AC,1min 2.5 | KV | |||||
| Applications |
·AC variable speed drives
·Static converters for DC motor drives
·Battery supplied applications
·Uninterruptible Power Supplies (UPS)
·Switched Mode Power Supplies (SMPS)
·Power supplies for welding applications
| Current | d | Connected | Terminal PIn Identification | |
| 1 | 0.5A-3A | 2-ø0.6 | 5,10 | 1...+15V 2...-15V 3...0V 4...Output 5.6,7...primary input current(+) 8,9,10...primary input current(-) |
| 2 | 5A,10A | 2-ø0.6 | 6,9 | |
| 3 | 20A | 4-ø1.6 | 6-7,8-9 |
1. All dimensions are in mm.
2. General tolerance ±1mm.
| Directions for use |
1. When the current will be measured goes through a sensor, the voltage will be measured at the output end. (Note: The false wiring may result in the damage of the sensor)
2. Custom design in the different rated input current and the output voltage are available.
| Standards |
·EN60947-1:2004
·IEC60950-1:2001
·EN50178:1998
·SJ 20790-2000
| General date |
| Value | Unit | |
| Operating temperature(TA) | -40 to +85 | ºC |
| Storage temperature(TS) | -40 to +125 | ºC |
| Mass(approx) (M) | 22 | g |
